Favicon Svethardware.cz  Svět hardware   Fórum Favicon Svetmobilne.cz  Svět mobilně   Fórum Favicon TVFreak.cz  TV Freak   Fórum Favicon Digimanie.cz  Digimanie   Fórum   Galerie Společnost oXy Online s.r.o.
Zobrazené výsledky: 1 až 14 z 14

Téma: Externi HDD nejde připojit

  1. #1
    Pravidelný diskutér Avatar uživatele kanabis
    Registrace
    Aug 2008
    Příspěvků
    257

    Nemůžu se dostak k obsahu externiho disku Maxtor One Touch Plus. Po připojení k přes USB Winy poznaji že jsem neco připojil ale oznamí chybu - Win 7 myslim chyba 42(zařízení oznámilo chybu), win xp s orig driverama to nerozpozna a Linux ani ťuk.
    Nejspíš to bude tím že jsem disk špatně odpojil a to tak že jsem šupem povytahoval kabely.
    Jak ho zase zprovoznit?
    Odpovídat lze po přihlášení

  2. #2
    Starousedlík SHW / Pilot TMF Avatar uživatele EditorPO
    Registrace
    May 2006
    Příspěvků
    2,897

    V tom pripade odisla skor elektronika v boxe. Ktory mas presne model? Nejaky starsi, alebo Maxtor OneTouch 4 Plus?

    Kym s nim nieco zacnes robit, tak by asi bolo lepsie vybrat disk, pripojit ho do priamo do PC a skopirovat data. Cim skor, tym lepsie.

    Maxtor OneTouch 4 Plus ma aj FireWire rozhranie. Skusal si ho?
    Odpovídat lze po přihlášení



  3. #3
    Pravidelný diskutér Avatar uživatele kanabis
    Registrace
    Aug 2008
    Příspěvků
    257

    mam 4 plus. dioda neblika ale sviti takze podle vyrobce zadny problem. firewire vyzkoušet nemuzu protoze ho nemam v PC. Linux ale myslim psal neco v tom smyslu ze ten disk si mysli ze je pouzivanej a ze mam ve windows ho bezpecne odebrat nebo pouzit nejaky prikaz v terminalu. A terminal nemusim tak jsem zkusil to v těch winch ale nic. podruhe se uz to neukazalo
    Odpovídat lze po přihlášení

  4. #4
    Starousedlík SHW / Pilot TMF Avatar uživatele EditorPO
    Registrace
    May 2006
    Příspěvků
    2,897

    Vyskusaj na inom pocitaci.
    Odpovídat lze po přihlášení

  5. #5
    Pravidelný diskutér Avatar uživatele kanabis
    Registrace
    Aug 2008
    Příspěvků
    257

    spatne jsem ho odpojil v jinem PC takze asi v nem ne?
    Odpovídat lze po přihlášení

  6. #6
    Starousedlík SHW / Pilot TMF Avatar uživatele EditorPO
    Registrace
    May 2006
    Příspěvků
    2,897

    Mozes aj v tom PC, ale este aj v dalsom.
    Odpovídat lze po přihlášení

  7. #7
    Pravidelný diskutér Avatar uživatele kanabis
    Registrace
    Aug 2008
    Příspěvků
    257

    a nevís o tom linux prikazu nebo o nekom kdo by vedel?
    Odpovídat lze po přihlášení



  8. #8
    Občasný diskutér Avatar uživatele bhujanga
    Registrace
    Aug 2007
    Příspěvků
    62

    V Linuxe mozes najprv hned po pripojeni USB HDD skusit prikaz dmesg | tail -n 25 . Tym vypises poslednych 25 riadkov bufferu so spravami jadra. Vo vypise by si mal najst nieco taketo (v mojom pripade je sa jedna o pripojenie USB kluca, ale pre USB HDD by sa to asi nemalo velmi lisit):

    [40867.225007] usb 1-4: new high speed USB device using ehci_hcd and address 18
    [40867.361928] usb 1-4: configuration #1 chosen from 1 choice
    [40867.437743] scsi15 : SCSI emulation for USB Mass Storage devices
    [40867.438017] usb 1-4: New USB device found, idVendor=0781, idProduct=5150
    [40867.438022] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
    [40867.438026] usb 1-4: Product: Cruzer Mini
    [40867.438029] usb 1-4: Manufacturer: SanDisk Corporation
    [40867.438032] usb 1-4: SerialNumber: SNDKA855C4082EF06405
    [40867.438042] usb-storage: device found at 18
    [40867.438045] usb-storage: waiting for device to settle before scanning
    [40873.136534] usb-storage: device scan complete
    [40873.152257] scsi 15:0:0:0: Direct-Access SanDisk Cruzer Mini 0.2 PQ: 0 ANSI: 2
    [40873.154472] sd 15:0:0:0: [sdg] 501759 512-byte hardware sectors (257 MB)
    [40873.154472] sd 15:0:0:0: [sdg] Write Protect is off
    [40873.154472] sd 15:0:0:0: [sdg] Mode Sense: 03 00 00 00
    [40873.154472] sd 15:0:0:0: [sdg] Assuming drive cache: write through
    [40873.158476] sd 15:0:0:0: [sdg] 501759 512-byte hardware sectors (257 MB)
    [40873.162477] sd 15:0:0:0: [sdg] Write Protect is off
    [40873.162477] sd 15:0:0:0: [sdg] Mode Sense: 03 00 00 00
    [40873.162477] sd 15:0:0:0: [sdg] Assuming drive cache: write through
    [40873.162519] sdg: sdg1
    [40873.166477] sd 15:0:0:0: [sdg] Attached SCSI removable disk
    [40873.166477] sd 15:0:0:0: Attached scsi generic sg7 type 0

    Znamena to ze jadro "vidi" nove zariadenie.
    Odpovídat lze po přihlášení

  9. #9
    Pravidelný diskutér Avatar uživatele kanabis
    Registrace
    Aug 2008
    Příspěvků
    257

    Linux hdd vidi. prikladam nekolikrat za sebou pouzity ten prikaz ( tez zde) Co s tím?
    Kód:
    dmesg | kanabis@ubuntu:~$ dmesg | tail -n 25
    [   45.948834] Buffer I/O error on device sdb, logical block 4
    [   45.948839] Buffer I/O error on device sdb, logical block 5
    [   45.948844] Buffer I/O error on device sdb, logical block 6
    [   45.948848] Buffer I/O error on device sdb, logical block 7
    [   45.948853] Buffer I/O error on device sdb, logical block 8
    [   45.948858] Buffer I/O error on device sdb, logical block 9
    [   45.948862] Buffer I/O error on device sdb, logical block 10
    [   45.948867] Buffer I/O error on device sdb, logical block 11
    [   46.124709] usb 1-8: reset high speed USB device using ehci_hcd and address 6
    [   46.124933] ADDRCONF(NETDEV_UP): eth0: link is not ready
    [   47.749237] tg3: eth0: Link is up at 100 Mbps, full duplex.
    [   47.749241] tg3: eth0: Flow control is on for TX and on for RX.
    [   47.749440] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [   58.244009] eth0: no IPv6 routers present
    [  118.036607] process `skype' is using obsolete setsockopt SO_BSDCOMPAT
    [ 1436.336078] usb 5-1: USB disconnect, address 2
    [ 1436.336214] btusb_intr_complete: hci0 urb f0939b00 failed to resubmit (19)
    [ 1436.336223] btusb_bulk_complete: hci0 urb efaf4900 failed to resubmit (19)
    [ 1436.337213] btusb_bulk_complete: hci0 urb efaf4a00 failed to resubmit (19)
    [ 1436.338016] btusb_send_frame: hci0 urb d33b4b00 submission failed
    [ 1451.780023] usb 1-7: new high speed USB device using ehci_hcd and address 7
    [ 1451.914388] usb 1-7: configuration #1 chosen from 1 choice
    [ 1451.914895] scsi7 : SCSI emulation for USB Mass Storage devices
    [ 1451.915321] usb-storage: device found at 7
    [ 1451.915325] usb-storage: waiting for device to settle before scanning
    kanabis@ubuntu:~$ dmesg | tail -n 25
    [   47.749241] tg3: eth0: Flow control is on for TX and on for RX.
    [   47.749440] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [   58.244009] eth0: no IPv6 routers present
    [  118.036607] process `skype' is using obsolete setsockopt SO_BSDCOMPAT
    [ 1436.336078] usb 5-1: USB disconnect, address 2
    [ 1436.336214] btusb_intr_complete: hci0 urb f0939b00 failed to resubmit (19)
    [ 1436.336223] btusb_bulk_complete: hci0 urb efaf4900 failed to resubmit (19)
    [ 1436.337213] btusb_bulk_complete: hci0 urb efaf4a00 failed to resubmit (19)
    [ 1436.338016] btusb_send_frame: hci0 urb d33b4b00 submission failed
    [ 1451.780023] usb 1-7: new high speed USB device using ehci_hcd and address 7
    [ 1451.914388] usb 1-7: configuration #1 chosen from 1 choice
    [ 1451.914895] scsi7 : SCSI emulation for USB Mass Storage devices
    [ 1451.915321] usb-storage: device found at 7
    [ 1451.915325] usb-storage: waiting for device to settle before scanning
    [ 1456.912207] usb-storage: device scan complete
    [ 1456.912796] scsi 7:0:0:0: Direct-Access     Maxtor   OneTouch         0121 PQ: 0 ANSI: 4
    [ 1456.914834] sd 7:0:0:0: [sdc] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
    [ 1456.915537] sd 7:0:0:0: [sdc] Write Protect is off
    [ 1456.915543] sd 7:0:0:0: [sdc] Mode Sense: 2d 08 00 00
    [ 1456.915548] sd 7:0:0:0: [sdc] Assuming drive cache: write through
    [ 1456.918041] sd 7:0:0:0: [sdc] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
    [ 1456.918910] sd 7:0:0:0: [sdc] Write Protect is off
    [ 1456.918917] sd 7:0:0:0: [sdc] Mode Sense: 2d 08 00 00
    [ 1456.918921] sd 7:0:0:0: [sdc] Assuming drive cache: write through
    [ 1456.918930]  sdc:
    kanabis@ubuntu:~$ dmesg | tail -n 25
    [   47.749241] tg3: eth0: Flow control is on for TX and on for RX.
    [   47.749440] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    [   58.244009] eth0: no IPv6 routers present
    [  118.036607] process `skype' is using obsolete setsockopt SO_BSDCOMPAT
    [ 1436.336078] usb 5-1: USB disconnect, address 2
    [ 1436.336214] btusb_intr_complete: hci0 urb f0939b00 failed to resubmit (19)
    [ 1436.336223] btusb_bulk_complete: hci0 urb efaf4900 failed to resubmit (19)
    [ 1436.337213] btusb_bulk_complete: hci0 urb efaf4a00 failed to resubmit (19)
    [ 1436.338016] btusb_send_frame: hci0 urb d33b4b00 submission failed
    [ 1451.780023] usb 1-7: new high speed USB device using ehci_hcd and address 7
    [ 1451.914388] usb 1-7: configuration #1 chosen from 1 choice
    [ 1451.914895] scsi7 : SCSI emulation for USB Mass Storage devices
    [ 1451.915321] usb-storage: device found at 7
    [ 1451.915325] usb-storage: waiting for device to settle before scanning
    [ 1456.912207] usb-storage: device scan complete
    [ 1456.912796] scsi 7:0:0:0: Direct-Access     Maxtor   OneTouch         0121 PQ: 0 ANSI: 4
    [ 1456.914834] sd 7:0:0:0: [sdc] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
    [ 1456.915537] sd 7:0:0:0: [sdc] Write Protect is off
    [ 1456.915543] sd 7:0:0:0: [sdc] Mode Sense: 2d 08 00 00
    [ 1456.915548] sd 7:0:0:0: [sdc] Assuming drive cache: write through
    [ 1456.918041] sd 7:0:0:0: [sdc] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
    [ 1456.918910] sd 7:0:0:0: [sdc] Write Protect is off
    [ 1456.918917] sd 7:0:0:0: [sdc] Mode Sense: 2d 08 00 00
    [ 1456.918921] sd 7:0:0:0: [sdc] Assuming drive cache: write through
    [ 1456.918930]  sdc:
    kanabis@ubuntu:~$ dmesg | tail -n 25
    [  118.036607] process `skype' is using obsolete setsockopt SO_BSDCOMPAT
    [ 1436.336078] usb 5-1: USB disconnect, address 2
    [ 1436.336214] btusb_intr_complete: hci0 urb f0939b00 failed to resubmit (19)
    [ 1436.336223] btusb_bulk_complete: hci0 urb efaf4900 failed to resubmit (19)
    [ 1436.337213] btusb_bulk_complete: hci0 urb efaf4a00 failed to resubmit (19)
    [ 1436.338016] btusb_send_frame: hci0 urb d33b4b00 submission failed
    [ 1451.780023] usb 1-7: new high speed USB device using ehci_hcd and address 7
    [ 1451.914388] usb 1-7: configuration #1 chosen from 1 choice
    [ 1451.914895] scsi7 : SCSI emulation for USB Mass Storage devices
    [ 1451.915321] usb-storage: device found at 7
    [ 1451.915325] usb-storage: waiting for device to settle before scanning
    [ 1456.912207] usb-storage: device scan complete
    [ 1456.912796] scsi 7:0:0:0: Direct-Access     Maxtor   OneTouch         0121 PQ: 0 ANSI: 4
    [ 1456.914834] sd 7:0:0:0: [sdc] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
    [ 1456.915537] sd 7:0:0:0: [sdc] Write Protect is off
    [ 1456.915543] sd 7:0:0:0: [sdc] Mode Sense: 2d 08 00 00
    [ 1456.915548] sd 7:0:0:0: [sdc] Assuming drive cache: write through
    [ 1456.918041] sd 7:0:0:0: [sdc] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
    [ 1456.918910] sd 7:0:0:0: [sdc] Write Protect is off
    [ 1456.918917] sd 7:0:0:0: [sdc] Mode Sense: 2d 08 00 00
    [ 1456.918921] sd 7:0:0:0: [sdc] Assuming drive cache: write through
    [ 1456.918930]  sdc:<6>usb 1-7: reset high speed USB device using ehci_hcd and address 7
    [ 1487.262957]  sdc1
    [ 1487.263807] sd 7:0:0:0: [sdc] Attached SCSI disk
    [ 1487.263948] sd 7:0:0:0: Attached scsi generic sg3 type 0
    kanabis@ubuntu:~$ dmesg | tail -n 25
    [  118.036607] process `skype' is using obsolete setsockopt SO_BSDCOMPAT
    [ 1436.336078] usb 5-1: USB disconnect, address 2
    [ 1436.336214] btusb_intr_complete: hci0 urb f0939b00 failed to resubmit (19)
    [ 1436.336223] btusb_bulk_complete: hci0 urb efaf4900 failed to resubmit (19)
    [ 1436.337213] btusb_bulk_complete: hci0 urb efaf4a00 failed to resubmit (19)
    [ 1436.338016] btusb_send_frame: hci0 urb d33b4b00 submission failed
    [ 1451.780023] usb 1-7: new high speed USB device using ehci_hcd and address 7
    [ 1451.914388] usb 1-7: configuration #1 chosen from 1 choice
    [ 1451.914895] scsi7 : SCSI emulation for USB Mass Storage devices
    [ 1451.915321] usb-storage: device found at 7
    [ 1451.915325] usb-storage: waiting for device to settle before scanning
    [ 1456.912207] usb-storage: device scan complete
    [ 1456.912796] scsi 7:0:0:0: Direct-Access     Maxtor   OneTouch         0121 PQ: 0 ANSI: 4
    [ 1456.914834] sd 7:0:0:0: [sdc] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
    [ 1456.915537] sd 7:0:0:0: [sdc] Write Protect is off
    [ 1456.915543] sd 7:0:0:0: [sdc] Mode Sense: 2d 08 00 00
    [ 1456.915548] sd 7:0:0:0: [sdc] Assuming drive cache: write through
    [ 1456.918041] sd 7:0:0:0: [sdc] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
    [ 1456.918910] sd 7:0:0:0: [sdc] Write Protect is off
    [ 1456.918917] sd 7:0:0:0: [sdc] Mode Sense: 2d 08 00 00
    [ 1456.918921] sd 7:0:0:0: [sdc] Assuming drive cache: write through
    [ 1456.918930]  sdc:<6>usb 1-7: reset high speed USB device using ehci_hcd and address 7
    [ 1487.262957]  sdc1
    [ 1487.263807] sd 7:0:0:0: [sdc] Attached SCSI disk
    [ 1487.263948] sd 7:0:0:0: Attached scsi generic sg3 type 0
    kanabis@ubuntu:~$ dmesg | tail -n 25
    [ 1519.211403] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211426] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211447] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211465] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211482] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211532] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211558] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211579] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211600] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211620] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211641] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211663] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211683] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211705] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.532035] usb 5-1: new full speed USB device using uhci_hcd and address 3
    [ 1519.652019] usb 5-1: device descriptor read/64, error -71
    [ 1519.876021] usb 5-1: device descriptor read/64, error -71
    [ 1520.092023] usb 5-1: new full speed USB device using uhci_hcd and address 4
    [ 1520.212021] usb 5-1: device descriptor read/64, error -71
    [ 1520.436025] usb 5-1: device descriptor read/64, error -71
    [ 1520.652025] usb 5-1: new full speed USB device using uhci_hcd and address 5
    [ 1521.060019] usb 5-1: device not accepting address 5, error -71
    [ 1521.172019] usb 5-1: new full speed USB device using uhci_hcd and address 6
    [ 1521.580019] usb 5-1: device not accepting address 6, error -71
    [ 1521.580036] hub 5-0:1.0: unable to enumerate USB device on port 1
    kanabis@ubuntu:~$ dmesg | tail -n 25
    [ 1519.211403] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211426] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211447] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211465] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211482] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211532] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211558] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211579] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211600] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211620] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211641] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211663] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211683] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.211705] sd 7:0:0:0: rejecting I/O to offline device
    [ 1519.532035] usb 5-1: new full speed USB device using uhci_hcd and address 3
    [ 1519.652019] usb 5-1: device descriptor read/64, error -71
    [ 1519.876021] usb 5-1: device descriptor read/64, error -71
    [ 1520.092023] usb 5-1: new full speed USB device using uhci_hcd and address 4
    [ 1520.212021] usb 5-1: device descriptor read/64, error -71
    [ 1520.436025] usb 5-1: device descriptor read/64, error -71
    [ 1520.652025] usb 5-1: new full speed USB device using uhci_hcd and address 5
    [ 1521.060019] usb 5-1: device not accepting address 5, error -71
    [ 1521.172019] usb 5-1: new full speed USB device using uhci_hcd and address 6
    [ 1521.580019] usb 5-1: device not accepting address 6, error -71
    [ 1521.580036] hub 5-0:1.0: unable to enumerate USB device on port 1
    kanabis@ubuntu:~$
    Odpovídat lze po přihlášení

  10. #10
    Občasný diskutér Avatar uživatele bhujanga
    Registrace
    Aug 2007
    Příspěvků
    62

    Tato cast vypisu vyzera celkom dobre (jadro rozpozna nove zariadenie a malo by byt mozne pripojit jeho particiu reprezentovanu specialnym suborom sdc1)

    [ 1451.780023] usb 1-7: new high speed USB device using ehci_hcd and address 7
    [ 1451.914388] usb 1-7: configuration #1 chosen from 1 choice
    [ 1451.914895] scsi7 : SCSI emulation for USB Mass Storage devices
    [ 1451.915321] usb-storage: device found at 7
    [ 1451.915325] usb-storage: waiting for device to settle before scanning
    [ 1456.912207] usb-storage: device scan complete
    [ 1456.912796] scsi 7:0:0:0: Direct-Access Maxtor OneTouch 0121 PQ: 0 ANSI: 4
    [ 1456.914834] sd 7:0:0:0: [sdc] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
    [ 1456.915537] sd 7:0:0:0: [sdc] Write Protect is off
    [ 1456.915543] sd 7:0:0:0: [sdc] Mode Sense: 2d 08 00 00
    [ 1456.915548] sd 7:0:0:0: [sdc] Assuming drive cache: write through
    [ 1456.918041] sd 7:0:0:0: [sdc] 1953525168 512-byte hardware sectors: (1.00 TB/931 GiB)
    [ 1456.918910] sd 7:0:0:0: [sdc] Write Protect is off
    [ 1456.918917] sd 7:0:0:0: [sdc] Mode Sense: 2d 08 00 00
    [ 1456.918921] sd 7:0:0:0: [sdc] Assuming drive cache: write through
    [ 1456.918930] sdc:<6>usb 1-7: reset high speed USB device using ehci_hcd and address 7
    [ 1487.262957] sdc1
    [ 1487.263807] sd 7:0:0:0: [sdc] Attached SCSI disk
    [ 1487.263948] sd 7:0:0:0: Attached scsi generic sg3 type 0

    Nasledujuce riadky uz ale nevyzeraju moc dobre:

    [ 1519.211403] sd 7:0:0:0: rejecting I/O to offline device
    ...
    [ 1519.652019] usb 5-1: device descriptor read/64, error -71

    Skusal som poprezerat nejake zdroje informacii a vyzera to viac na softwareovu chybu ako hardwareovu (mozne su obidve). Neviem ani ci ide o dve nezavisle chyby (viz. dva riadky vypisu vyssie), alebo ci so sebou nejako viac suvisia. Zvlastne je ze ze sa chyba prejavuje aj v OS Windows.
    Mozes skusit poodpajat vsetky USB zariadenia okrem tych ktore nevyhnutne potrebujes (asi len mys a klavesnica). V Linuxe potom skus prikaz

    echo Y > /sys/module/usbcore/parameters/old_scheme_first

    (s pravami roota). Potom pripoj USB HDD, pockaj cca minutu a posli vypis celeho bufferu jadra. Vypis mozes ziskat prikazom

    dmesg > /home/$USER/dmesg.txt

    (v tvojom domovskom adresary sa vytvori textovy subor dmesg.txt obsahujuci vysutp prikazu dmesg).
    Od urcitej verzie linuxoveho jadra sa pouziva schema "indexovania" USB zariadeni podobna ako v OS Windows (preto mozes tuto moznost vyskusat ako prvu). Ze vraj niektore zariadenia sposobuju chyby (error -71) pri pouziti tejto prvej schemy a prave prikazom echo Y > ... si vynutis aby sa pouzila druha schema. Po restarte systemu bude zmena v subore old_scheme_first stratena ale to by nemalo vadit ak to nepomoze.
    Dalej mozes vyskusat pripojit HDD bud za behu PC (resp. OS) alebo pri vypnutom PC.
    Naposledy upraveno uživatelem bhujanga: 15-07-2009 v 21:56
    Odpovídat lze po přihlášení

  11. #11
    Pravidelný diskutér Avatar uživatele kanabis
    Registrace
    Aug 2008
    Příspěvků
    257

    prikaz pouzit a tohle bude cast o disku
    Kód:
    [  663.364038] usb 1-7: new high speed USB device using ehci_hcd and address 5
    [  663.386038] usb 1-7: configuration #1 chosen from 1 choice
    [  663.386531] scsi7 : SCSI emulation for USB Mass Storage devices
    [  663.398800] usb-storage: device found at 5
    [  663.398804] usb-storage: waiting for device to settle before scanning
    [  668.396192] usb-storage: device scan complete
    [  668.512021] usb 1-7: reset high speed USB device using ehci_hcd and address 5
    [  675.112031] usb 1-7: reset high speed USB device using ehci_hcd and address 5
    [  675.134046] usb 1-7: device firmware changed
    [  675.134088] scsi 7:0:0:0: Device offlined - not ready after error recovery
    [  675.134126] usb 1-7: USB disconnect, address 5
    [  675.452525] usb 5-1: new full speed USB device using uhci_hcd and address 2
    [  675.864024] usb 5-1: device not accepting address 2, error -71
    [  675.976021] usb 5-1: new full speed USB device using uhci_hcd and address 3
    [  676.384020] usb 5-1: device not accepting address 3, error -71
    [  676.496017] usb 5-1: new full speed USB device using uhci_hcd and address 4
    [  676.616017] usb 5-1: device descriptor read/64, error -71
    [  676.840030] usb 5-1: device descriptor read/64, error -71
    [  677.056019] usb 5-1: new full speed USB device using uhci_hcd and address 5
    [  677.176017] usb 5-1: device descriptor read/64, error -71
    [  677.400020] usb 5-1: device descriptor read/64, error -71
    [  677.504028] hub 5-0:1.0: unable to enumerate USB device on port 1
    v priloze cely soubor
    take se mi podarilo vyhrabat firewire kabel a pripojit to pomoci neho. vypisi prikladam sic to vypada ze to radsi neudelalo nic( v druhem vypisu uz mam webku btw: nefunguje ji obraz a pak asi tiskarnu ale nejsem si jist). chyba ale muze byt v firewire radici
    Připojené soubory Připojené soubory
    Odpovídat lze po přihlášení

  12. #12
    Občasný diskutér Avatar uživatele bhujanga
    Registrace
    Aug 2007
    Příspěvků
    62

    Priznam as ze uz neviem co by mohlo vyriesit problem s USB pripojenim. Skusal si Firewire aj vo Windows ? Ak je tvoj Firewire radic podporovany v Linuxe, musis mat zavedene potrebne moduly pre jadro.

    Mozes sem skusit vlozit vyvpis zavedenych modulov pri pripojenom Firewire HDD lsmod > /home/$USER/lsmod.txt .
    Naposledy upraveno uživatelem bhujanga: 24-07-2009 v 10:22
    Odpovídat lze po přihlášení



  13. #13
    Pravidelný diskutér Avatar uživatele kanabis
    Registrace
    Aug 2008
    Příspěvků
    257

    ten fire wire asi nefunguje. ve win do neudelal take nic
    po pripojeni prez USB to chtelo instnou ovladac ale nepovedlo se a ve spravci zarideni to ukazovalo tuto chybu
    Kód:
    Zařízení bylo zastaveno, protože oznámilo potíže. (Kód 43)
    nevíš o nějakém geekovi ktery by vedel?
    Odpovídat lze po přihlášení

  14. #14
    Občasný diskutér Avatar uživatele bhujanga
    Registrace
    Aug 2007
    Příspěvků
    62

    Citace Původně odesláno od kanabis Zobrazit příspěvek
    nevíš o nějakém geekovi ktery by vedel?
    Nechcem robit reklamu ale mozes skusit na abclinuxu.cz .

    Ak este budes na Linuxe, mozes pripojit HDD cez USB a skusit odstranit modul ehci_hcd prikazom modprobe -r ehci_hcd .
    Odpovídat lze po přihlášení

Podobná témata

  1. Nejde se připojit k wifi
    Od G.i.k v sekci Sítě
    Reakcí: 10
    Poslední příspěvek: 28-01-2013, 19:13
  2. Nejde pripojit externi hdd
    Od esetik v sekci Problémy s PC (HW/SW) a řešení
    Reakcí: 17
    Poslední příspěvek: 22-03-2011, 00:50
  3. nejde mi pripojit iso k virtualboxu
    Od matata v sekci Problémy s PC (HW/SW) a řešení
    Reakcí: 13
    Poslední příspěvek: 21-04-2010, 18:42
  4. Externí disk WD nelze připojit
    Od David SSS v sekci Problémy s PC (HW/SW) a řešení
    Reakcí: 17
    Poslední příspěvek: 13-11-2009, 21:41
  5. Jak připojit NTB mechaniku jako externí k PC ?
    Od BADMOPAR v sekci Optické mechaniky
    Reakcí: 7
    Poslední příspěvek: 03-08-2009, 23:56